1#Uncommenting these urls would only enable
2#the power up auto injection and force injection(test case).
3#XTRA_SERVER_1=http://xtrapath1.izatcloud.net/xtra2.bin
4#XTRA_SERVER_2=http://xtrapath2.izatcloud.net/xtra2.bin
5#XTRA_SERVER_3=http://xtrapath3.izatcloud.net/xtra2.bin
6
7#Version check for XTRA
8#DISABLE = 0
9#AUTO    = 1
10#XTRA2   = 2
11#XTRA3   = 3
12XTRA_VERSION_CHECK=0
13
14# Error Estimate
15# _SET = 1
16# _CLEAR = 0
17ERR_ESTIMATE=0
18
19#NTP server
20NTP_SERVER=time.izatcloud.net
21
22#XTRA CA path
23XTRA_CA_PATH=/system/etc/security/cacerts
24
25# DEBUG LEVELS: 0 - none, 1 - Error, 2 - Warning, 3 - Info
26#               4 - Debug, 5 - Verbose
27# If DEBUG_LEVEL is commented, Android's logging levels will be used
28DEBUG_LEVEL = 3
29
30# Intermediate position report, 1=enable, 0=disable
31INTERMEDIATE_POS=0
32
33# Below bit mask configures how GPS functionalities
34# should be locked when user turns off GPS on Settings
35# Set bit 0x1 if MO GPS functionalities are to be locked
36# Set bit 0x2 if NI GPS functionalities are to be locked
37# default - non is locked for backward compatibility
38#GPS_LOCK = 0
39
40# supl version 1.0
41SUPL_VER=0x10000
42
43# Emergency SUPL, 1=enable, 0=disable
44#SUPL_ES=0
45
46#Choose PDN for Emergency SUPL
47#1 - Use emergency PDN
48#0 - Use regular SUPL PDN for Emergency SUPL
49#USE_EMERGENCY_PDN_FOR_EMERGENCY_SUPL=0
50
51#SUPL_MODE is a bit mask set in config.xml per carrier by default.
52#If it is uncommented here, this value will overwrite the value from
53#config.xml.
54#MSA=0X2
55#MSB=0X1
56#SUPL_MODE=
57
58# GPS Capabilities bit mask
59# SCHEDULING = 0x01
60# MSB = 0x02
61# MSA = 0x04
62# ON_DEMAND_TIME = 0x10
63# GEOFENCE = 0x20
64# default = ON_DEMAND_TIME | MSA | MSB | SCHEDULING | GEOFENCE
65CAPABILITIES=0x37
66
67# Accuracy threshold for intermediate positions
68# less accurate positions are ignored, 0 for passing all positions
69# ACCURACY_THRES=5000
70
71################################
72##### AGPS server settings #####
73################################
74
75# FOR SUPL SUPPORT, set the following
76# SUPL_HOST=supl.host.com or IP
77# SUPL_PORT=1234
78
79# FOR C2K PDE SUPPORT, set the following
80# C2K_HOST=c2k.pde.com or IP
81# C2K_PORT=1234
82
83# Bitmask of slots that are available
84# for write/install to, where 1s indicate writable,
85# and the default value is 0 where no slots
86# are writable. For example, AGPS_CERT_WRITABLE_MASK
87# of b1000001010 makes 3 slots available
88# and the remaining 7 slots unwritable.
89#AGPS_CERT_WRITABLE_MASK=0
90
91####################################
92#  LTE Positioning Profile Settings
93####################################
94# 0: Enable RRLP on LTE(Default)
95# 1: Enable LPP_User_Plane on LTE
96# 2: Enable LPP_Control_Plane
97# 3: Enable both LPP_User_Plane and LPP_Control_Plane
98LPP_PROFILE = 2
99
100################################
101# EXTRA SETTINGS
102################################
103# NMEA provider (1=Modem Processor, 0=Application Processor)
104NMEA_PROVIDER=0
105# Mark if it is a SGLTE target (1=SGLTE, 0=nonSGLTE)
106SGLTE_TARGET=0
107
108##################################################
109# Select Positioning Protocol on A-GLONASS system
110##################################################
111# 0x1: RRC CPlane
112# 0x2: RRLP UPlane
113# 0x4: LLP Uplane
114A_GLONASS_POS_PROTOCOL_SELECT = 0
115
116##################################################
117# Select technology for LPPe Control Plane
118##################################################
119# 0x1: DBH for LPPe CP
120# 0x2: WLAN AP Measurements for LPPe CP
121LPPE_CP_TECHNOLOGY = 0
122
123##################################################
124# Select technology for LPPe User Plane
125##################################################
126# 0x1: DBH for LPPe UP
127# 0x2: WLAN AP Measurements for LPPe UP
128LPPE_UP_TECHNOLOGY = 0
129
130# AP Coarse Timestamp Uncertainty
131##################################################
132# default : 10
133# or as per clock uncertainty of product
134AP_TIMESTAMP_UNCERTAINTY = 10
135
136#####################################
137# GNSS PPS settings
138#####################################
139#AP DR engine availability status
140# 0 : NO AP DR (default)
141# 1 : AP DR enabled
142#EXTERNAL_DR_ENABLED = 0
143
144#####################################
145#DR_SYNC Pulse Availability
146#####################################
147# 0 : DR_SYNC pulse not available (default)
148# 1 : DR_SYNC pulse available
149DR_SYNC_ENABLED = 0
150
151#####################################
152#PPS Device name
153#####################################
154PPS_DEVICENAME = /dev/pps0
155
156#####################################
157#AP Clock Accuracy
158#####################################
159AP_CLOCK_PPM = 100
160
161#####################################
162#MAX ms difference to detect missing pulse
163#####################################
164MISSING_PULSE_TIME_DELTA = 900
165
166#####################################
167#Propagation time uncertainty
168#####################################
169PROPAGATION_TIME_UNCERTAINTY = 1
170