Home
last modified time | relevance | path

Searched refs:band (Results 1 – 10 of 10) sorted by relevance

/device/generic/goldfish/wifi/wifi_hal/
Dinterface.cpp152 wifi_error Interface::getValidChannels(int band, in getValidChannels() argument
159 switch (band) { in getValidChannels()
Dinterface.h47 wifi_error getValidChannels(int band,
Dwifi_hal.cpp230 int band, in wifi_get_valid_channels() argument
239 return asInterface(handle)->getValidChannels(band, in wifi_get_valid_channels()
/device/google/bonito/
DWCNSS_qcom_cfg.ini129 #Preferred band (both or 2.4 only or 5 only)
149 # 2-Force SCC if same band, with SAP restart
150 # 3-Force SCC if same band, without SAP restart by sending (E)CSA
151 # 4-Force SCC if same band (or) use SAP mandatory channel for DBS,
369 # To enable, set gRoamIntraBand=1 (Roaming within band)
370 # To disable, set gRoamIntraBand=0 (Roaming across band)
535 # configure tx and rx per band chain mask. These parameters will
/device/google/crosshatch/
DWCNSS_qcom_cfg.ini129 #Preferred band (both or 2.4 only or 5 only)
149 # 2-Force SCC if same band, with SAP restart
150 # 3-Force SCC if same band, without SAP restart by sending (E)CSA
151 # 4-Force SCC if same band (or) use SAP mandatory channel for DBS,
369 # To enable, set gRoamIntraBand=1 (Roaming within band)
370 # To disable, set gRoamIntraBand=0 (Roaming across band)
535 # configure tx and rx per band chain mask. These parameters will
/device/google/coral/
DWCNSS_qcom_cfg.ini73 # 2-Force SCC if same band, with SAP restart
74 # 3-Force SCC if same band, without SAP restart by sending (E)CSA
75 # 4-Force SCC if same band (or) use SAP mandatory channel for DBS,
325 # This ini is used to set probe request rate to 5.5Mbps as per OCE requirement in 2.4G band
351 # Set channel selection logic for different concurrency combinations to DBS or inter band MCC.
353 # 0 - inter-band MCC
/device/linaro/poplar/wifi/wifi_hal/
Dgscan.cpp250 int band; member in GetChannelListCommand
253 int num_max_ch, int band) in GetChannelListCommand() argument
255 max_channels(num_max_ch), num_channels(ch_num), band(band) in GetChannelListCommand()
268 ret = mMsg.put_u32(GSCAN_ATTRIBUTE_BAND, band); in create()
321 int band, int max_channels, wifi_channel *channels, int *num_channels) in wifi_get_valid_channels() argument
507 mParams->buckets[i].band); in createSetupRequest()
/device/google/muskie/
DWCNSS_qcom_cfg.ini130 #Preferred band (both or 2.4 only or 5 only)
152 # MCC to SCC Switch mode: 0-Disable 1-Enable 2-Force SCC if same band
384 # To enable, set gRoamIntraBand=1 (Roaming within band)
385 # To disable, set gRoamIntraBand=0 (Roaming across band)
/device/google/taimen/
DWCNSS_qcom_cfg.ini130 #Preferred band (both or 2.4 only or 5 only)
152 # MCC to SCC Switch mode: 0-Disable 1-Enable 2-Force SCC if same band
384 # To enable, set gRoamIntraBand=1 (Roaming within band)
385 # To disable, set gRoamIntraBand=0 (Roaming across band)
/device/linaro/dragonboard/db845c/firmware/
Dadsp.b131 …band get param rsp payload���vpm_apr_msg_handler.cpp:vpm_get_param_v3_cmd_ctrl(): Failed to valida…
32 …band on device_id:%hu�AudDevMgr.cpp:ADM: Physical memory address is not aligned to cache line, in …