1# 2#* Copyright (C) 2016 The Android Open Source Project 3#* 4#* Licensed under the Apache License, Version 2.0 (the "License"); 5#* you may not use this file except in compliance with the License. 6#* You may obtain a copy of the License at 7#* 8#* http://www.apache.org/licenses/LICENSE-2.0 9#* 10#* Unless required by applicable law or agreed to in writing, software 11#* distributed under the License is distributed on an "AS IS" BASIS, 12#* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. 13#* See the License for the specific language governing permissions and 14#* limitations under the License. 15# 16##### hostapd configuration file ############################################## 17# Empty lines and lines starting with # are ignored 18 19# AP netdevice name (without 'ap' postfix, i.e., wlan0 uses wlan0ap for 20# management frames); ath0 for madwifi 21interface=wlan1 22 23# In case of madwifi, atheros, and nl80211 driver interfaces, an additional 24# configuration parameter, bridge, may be used to notify hostapd if the 25# interface is included in a bridge. This parameter is not used with Host AP 26# driver. If the bridge parameter is not set, the drivers will automatically 27# figure out the bridge interface (assuming sysfs is enabled and mounted to 28# /sys) and this parameter may not be needed. 29# 30# For nl80211, this parameter can be used to request the AP interface to be 31# added to the bridge automatically (brctl may refuse to do this before hostapd 32# has been started to change the interface mode). If needed, the bridge 33# interface is also created. 34#bridge=br0 35 36# Driver interface type (hostap/wired/madwifi/test/none/nl80211/bsd); 37# default: hostap). nl80211 is used with all Linux mac80211 drivers. 38# Use driver=none if building hostapd as a standalone RADIUS server that does 39# not control any wireless/wired driver. 40# driver=hostap 41driver=nl80211 42# hostapd event logger configuration 43# 44# Two output method: syslog and stdout (only usable if not forking to 45# background). 46# 47# Module bitfield (ORed bitfield of modules that will be logged; -1 = all 48# modules): 49# bit 0 (1) = IEEE 802.11 50# bit 1 (2) = IEEE 802.1X 51# bit 2 (4) = RADIUS 52# bit 3 (8) = WPA 53# bit 4 (16) = driver interface 54# bit 5 (32) = IAPP 55# bit 6 (64) = MLME 56# 57# Levels (minimum value for logged events): 58# 0 = verbose debugging 59# 1 = debugging 60# 2 = informational messages 61# 3 = notification 62# 4 = warning 63# 64logger_syslog=-1 65logger_syslog_level=2 66logger_stdout=-1 67logger_stdout_level=2 68 69# Interface for separate control program. If this is specified, hostapd 70# will create this directory and a UNIX domain socket for listening to requests 71# from external programs (CLI/GUI, etc.) for status information and 72# configuration. The socket file will be named based on the interface name, so 73# multiple hostapd processes/interfaces can be run at the same time if more 74# than one interface is used. 75# /var/run/hostapd is the recommended directory for sockets and by default, 76# hostapd_cli will use it when trying to connect with hostapd. 77#ctrl_interface=/data/local/wifi/sockets 78 79# Access control for the control interface can be configured by setting the 80# directory to allow only members of a group to use sockets. This way, it is 81# possible to run hostapd as root (since it needs to change network 82# configuration and open raw sockets) and still allow GUI/CLI components to be 83# run as non-root users. However, since the control interface can be used to 84# change the network configuration, this access needs to be protected in many 85# cases. By default, hostapd is configured to use gid 0 (root). If you 86# want to allow non-root users to use the contron interface, add a new group 87# and change this value to match with that group. Add users that should have 88# control interface access to this group. 89# 90# This variable can be a group name or gid. 91#ctrl_interface_group=wheel 92ctrl_interface_group=0 93 94 95##### IEEE 802.11 related configuration ####################################### 96 97# SSID to be used in IEEE 802.11 management frames 98ssid=AndroidWifi 99# Alternative formats for configuring SSID 100# (double quoted string, hexdump, printf-escaped string) 101#ssid2="test" 102#ssid2=74657374 103#ssid2=P"hello\nthere" 104 105# UTF-8 SSID: Whether the SSID is to be interpreted using UTF-8 encoding 106#utf8_ssid=1 107 108# Country code (ISO/IEC 3166-1). Used to set regulatory domain. 109# Set as needed to indicate country in which device is operating. 110# This can limit available channels and transmit power. 111country_code=US 112 113# Enable IEEE 802.11d. This advertises the country_code and the set of allowed 114# channels and transmit power levels based on the regulatory limits. The 115# country_code setting must be configured with the correct country for 116# IEEE 802.11d functions. 117# (default: 0 = disabled) 118#ieee80211d=1 119 120# Enable IEEE 802.11h. This enables radar detection and DFS support if 121# available. DFS support is required on outdoor 5 GHz channels in most countries 122# of the world. This can be used only with ieee80211d=1. 123# (default: 0 = disabled) 124#ieee80211h=1 125 126# Add Power Constraint element to Beacon and Probe Response frames 127# This config option adds Power Constraint element when applicable and Country 128# element is added. Power Constraint element is required by Transmit Power 129# Control. This can be used only with ieee80211d=1. 130# Valid values are 0..255. 131#local_pwr_constraint=3 132 133# Set Spectrum Management subfield in the Capability Information field. 134# This config option forces the Spectrum Management bit to be set. When this 135# option is not set, the value of the Spectrum Management bit depends on whether 136# DFS or TPC is required by regulatory authorities. This can be used only with 137# ieee80211d=1 and local_pwr_constraint configured. 138#spectrum_mgmt_required=1 139 140# Operation mode (a = IEEE 802.11a, b = IEEE 802.11b, g = IEEE 802.11g, 141# ad = IEEE 802.11ad (60 GHz); a/g options are used with IEEE 802.11n, too, to 142# specify band) 143# Default: IEEE 802.11b 144hw_mode=g 145 146# Channel number (IEEE 802.11) 147# (default: 0, i.e., not set) 148# Please note that some drivers do not use this value from hostapd and the 149# channel will need to be configured separately with iwconfig. 150# 151# If CONFIG_ACS build option is enabled, the channel can be selected 152# automatically at run time by setting channel=acs_survey or channel=0, both of 153# which will enable the ACS survey based algorithm. 154channel=8 155 156# ACS tuning - Automatic Channel Selection 157# See: http://wireless.kernel.org/en/users/Documentation/acs 158# 159# You can customize the ACS survey algorithm with following variables: 160# 161# acs_num_scans requirement is 1..100 - number of scans to be performed that 162# are used to trigger survey data gathering of an underlying device driver. 163# Scans are passive and typically take a little over 100ms (depending on the 164# driver) on each available channel for given hw_mode. Increasing this value 165# means sacrificing startup time and gathering more data wrt channel 166# interference that may help choosing a better channel. This can also help fine 167# tune the ACS scan time in case a driver has different scan dwell times. 168# 169# Defaults: 170#acs_num_scans=5 171 172# Channel list restriction. This option allows hostapd to select one of the 173# provided channels when a channel should be automatically selected. This 174# is currently only used for DFS when the current channels becomes unavailable 175# due to radar interference, and is currently only useful when ieee80211h=1 is 176# set. 177# Default: not set (allow any enabled channel to be selected) 178#chanlist=100 104 108 112 116 179 180# Beacon interval in kus (1.024 ms) (default: 100; range 15..65535) 181beacon_int=100 182 183# DTIM (delivery traffic information message) period (range 1..255): 184# number of beacons between DTIMs (1 = every beacon includes DTIM element) 185# (default: 2) 186dtim_period=2 187 188# Maximum number of stations allowed in station table. New stations will be 189# rejected after the station table is full. IEEE 802.11 has a limit of 2007 190# different association IDs, so this number should not be larger than that. 191# (default: 2007) 192max_num_sta=255 193 194# RTS/CTS threshold; 2347 = disabled (default); range 0..2347 195# If this field is not included in hostapd.conf, hostapd will not control 196# RTS threshold and 'iwconfig wlan# rts <val>' can be used to set it. 197rts_threshold=2347 198 199# Fragmentation threshold; 2346 = disabled (default); range 256..2346 200# If this field is not included in hostapd.conf, hostapd will not control 201# fragmentation threshold and 'iwconfig wlan# frag <val>' can be used to set 202# it. 203fragm_threshold=2346 204 205# Rate configuration 206# Default is to enable all rates supported by the hardware. This configuration 207# item allows this list be filtered so that only the listed rates will be left 208# in the list. If the list is empty, all rates are used. This list can have 209# entries that are not in the list of rates the hardware supports (such entries 210# are ignored). The entries in this list are in 100 kbps, i.e., 11 Mbps = 110. 211# If this item is present, at least one rate have to be matching with the rates 212# hardware supports. 213# default: use the most common supported rate setting for the selected 214# hw_mode (i.e., this line can be removed from configuration file in most 215# cases) 216#supported_rates=10 20 55 110 60 90 120 180 240 360 480 540 217 218# Basic rate set configuration 219# List of rates (in 100 kbps) that are included in the basic rate set. 220# If this item is not included, usually reasonable default set is used. 221#basic_rates=10 20 222#basic_rates=10 20 55 110 223#basic_rates=60 120 240 224 225# Short Preamble 226# This parameter can be used to enable optional use of short preamble for 227# frames sent at 2 Mbps, 5.5 Mbps, and 11 Mbps to improve network performance. 228# This applies only to IEEE 802.11b-compatible networks and this should only be 229# enabled if the local hardware supports use of short preamble. If any of the 230# associated STAs do not support short preamble, use of short preamble will be 231# disabled (and enabled when such STAs disassociate) dynamically. 232# 0 = do not allow use of short preamble (default) 233# 1 = allow use of short preamble 234#preamble=1 235 236# Station MAC address -based authentication 237# Please note that this kind of access control requires a driver that uses 238# hostapd to take care of management frame processing and as such, this can be 239# used with driver=hostap or driver=nl80211, but not with driver=madwifi. 240# 0 = accept unless in deny list 241# 1 = deny unless in accept list 242# 2 = use external RADIUS server (accept/deny lists are searched first) 243macaddr_acl=0 244 245# Accept/deny lists are read from separate files (containing list of 246# MAC addresses, one per line). Use absolute path name to make sure that the 247# files can be read on SIGHUP configuration reloads. 248#accept_mac_file=/etc/hostapd.accept 249#deny_mac_file=/etc/hostapd.deny 250 251# IEEE 802.11 specifies two authentication algorithms. hostapd can be 252# configured to allow both of these or only one. Open system authentication 253# should be used with IEEE 802.1X. 254# Bit fields of allowed authentication algorithms: 255# bit 0 = Open System Authentication 256# bit 1 = Shared Key Authentication (requires WEP) 257auth_algs=3 258 259# Send empty SSID in beacons and ignore probe request frames that do not 260# specify full SSID, i.e., require stations to know SSID. 261# default: disabled (0) 262# 1 = send empty (length=0) SSID in beacon and ignore probe request for 263# broadcast SSID 264# 2 = clear SSID (ASCII 0), but keep the original length (this may be required 265# with some clients that do not support empty SSID) and ignore probe 266# requests for broadcast SSID 267ignore_broadcast_ssid=0 268 269# Additional vendor specfic elements for Beacon and Probe Response frames 270# This parameter can be used to add additional vendor specific element(s) into 271# the end of the Beacon and Probe Response frames. The format for these 272# element(s) is a hexdump of the raw information elements (id+len+payload for 273# one or more elements) 274#vendor_elements=dd0411223301 275 276# TX queue parameters (EDCF / bursting) 277# tx_queue_<queue name>_<param> 278# queues: data0, data1, data2, data3, after_beacon, beacon 279# (data0 is the highest priority queue) 280# parameters: 281# aifs: AIFS (default 2) 282# cwmin: cwMin (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023) 283# cwmax: cwMax (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023); cwMax >= cwMin 284# burst: maximum length (in milliseconds with precision of up to 0.1 ms) for 285# bursting 286# 287# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e): 288# These parameters are used by the access point when transmitting frames 289# to the clients. 290# 291# Low priority / AC_BK = background 292#tx_queue_data3_aifs=7 293#tx_queue_data3_cwmin=15 294#tx_queue_data3_cwmax=1023 295#tx_queue_data3_burst=0 296# Note: for IEEE 802.11b mode: cWmin=31 cWmax=1023 burst=0 297# 298# Normal priority / AC_BE = best effort 299#tx_queue_data2_aifs=3 300#tx_queue_data2_cwmin=15 301#tx_queue_data2_cwmax=63 302#tx_queue_data2_burst=0 303# Note: for IEEE 802.11b mode: cWmin=31 cWmax=127 burst=0 304# 305# High priority / AC_VI = video 306#tx_queue_data1_aifs=1 307#tx_queue_data1_cwmin=7 308#tx_queue_data1_cwmax=15 309#tx_queue_data1_burst=3.0 310# Note: for IEEE 802.11b mode: cWmin=15 cWmax=31 burst=6.0 311# 312# Highest priority / AC_VO = voice 313#tx_queue_data0_aifs=1 314#tx_queue_data0_cwmin=3 315#tx_queue_data0_cwmax=7 316#tx_queue_data0_burst=1.5 317# Note: for IEEE 802.11b mode: cWmin=7 cWmax=15 burst=3.3 318 319# 802.1D Tag (= UP) to AC mappings 320# WMM specifies following mapping of data frames to different ACs. This mapping 321# can be configured using Linux QoS/tc and sch_pktpri.o module. 322# 802.1D Tag 802.1D Designation Access Category WMM Designation 323# 1 BK AC_BK Background 324# 2 - AC_BK Background 325# 0 BE AC_BE Best Effort 326# 3 EE AC_BE Best Effort 327# 4 CL AC_VI Video 328# 5 VI AC_VI Video 329# 6 VO AC_VO Voice 330# 7 NC AC_VO Voice 331# Data frames with no priority information: AC_BE 332# Management frames: AC_VO 333# PS-Poll frames: AC_BE 334 335# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e): 336# for 802.11a or 802.11g networks 337# These parameters are sent to WMM clients when they associate. 338# The parameters will be used by WMM clients for frames transmitted to the 339# access point. 340# 341# note - txop_limit is in units of 32microseconds 342# note - acm is admission control mandatory flag. 0 = admission control not 343# required, 1 = mandatory 344# note - here cwMin and cmMax are in exponent form. the actual cw value used 345# will be (2^n)-1 where n is the value given here 346# 347wmm_enabled=1 348# 349# WMM-PS Unscheduled Automatic Power Save Delivery [U-APSD] 350# Enable this flag if U-APSD supported outside hostapd (eg., Firmware/driver) 351#uapsd_advertisement_enabled=1 352# 353# Low priority / AC_BK = background 354wmm_ac_bk_cwmin=4 355wmm_ac_bk_cwmax=10 356wmm_ac_bk_aifs=7 357wmm_ac_bk_txop_limit=0 358wmm_ac_bk_acm=0 359# Note: for IEEE 802.11b mode: cWmin=5 cWmax=10 360# 361# Normal priority / AC_BE = best effort 362wmm_ac_be_aifs=3 363wmm_ac_be_cwmin=4 364wmm_ac_be_cwmax=10 365wmm_ac_be_txop_limit=0 366wmm_ac_be_acm=0 367# Note: for IEEE 802.11b mode: cWmin=5 cWmax=7 368# 369# High priority / AC_VI = video 370wmm_ac_vi_aifs=2 371wmm_ac_vi_cwmin=3 372wmm_ac_vi_cwmax=4 373wmm_ac_vi_txop_limit=94 374wmm_ac_vi_acm=0 375# Note: for IEEE 802.11b mode: cWmin=4 cWmax=5 txop_limit=188 376# 377# Highest priority / AC_VO = voice 378wmm_ac_vo_aifs=2 379wmm_ac_vo_cwmin=2 380wmm_ac_vo_cwmax=3 381wmm_ac_vo_txop_limit=47 382wmm_ac_vo_acm=0 383# Note: for IEEE 802.11b mode: cWmin=3 cWmax=4 burst=102 384 385# Static WEP key configuration 386# 387# The key number to use when transmitting. 388# It must be between 0 and 3, and the corresponding key must be set. 389# default: not set 390#wep_default_key=0 391# The WEP keys to use. 392# A key may be a quoted string or unquoted hexadecimal digits. 393# The key length should be 5, 13, or 16 characters, or 10, 26, or 32 394# digits, depending on whether 40-bit (64-bit), 104-bit (128-bit), or 395# 128-bit (152-bit) WEP is used. 396# Only the default key must be supplied; the others are optional. 397# default: not set 398#wep_key0=123456789a 399#wep_key1="vwxyz" 400#wep_key2=0102030405060708090a0b0c0d 401#wep_key3=".2.4.6.8.0.23" 402 403# Station inactivity limit 404# 405# If a station does not send anything in ap_max_inactivity seconds, an 406# empty data frame is sent to it in order to verify whether it is 407# still in range. If this frame is not ACKed, the station will be 408# disassociated and then deauthenticated. This feature is used to 409# clear station table of old entries when the STAs move out of the 410# range. 411# 412# The station can associate again with the AP if it is still in range; 413# this inactivity poll is just used as a nicer way of verifying 414# inactivity; i.e., client will not report broken connection because 415# disassociation frame is not sent immediately without first polling 416# the STA with a data frame. 417# default: 300 (i.e., 5 minutes) 418#ap_max_inactivity=300 419# 420# The inactivity polling can be disabled to disconnect stations based on 421# inactivity timeout so that idle stations are more likely to be disconnected 422# even if they are still in range of the AP. This can be done by setting 423# skip_inactivity_poll to 1 (default 0). 424#skip_inactivity_poll=0 425 426# Disassociate stations based on excessive transmission failures or other 427# indications of connection loss. This depends on the driver capabilities and 428# may not be available with all drivers. 429#disassoc_low_ack=1 430 431# Maximum allowed Listen Interval (how many Beacon periods STAs are allowed to 432# remain asleep). Default: 65535 (no limit apart from field size) 433#max_listen_interval=100 434 435# WDS (4-address frame) mode with per-station virtual interfaces 436# (only supported with driver=nl80211) 437# This mode allows associated stations to use 4-address frames to allow layer 2 438# bridging to be used. 439#wds_sta=1 440 441# If bridge parameter is set, the WDS STA interface will be added to the same 442# bridge by default. This can be overridden with the wds_bridge parameter to 443# use a separate bridge. 444#wds_bridge=wds-br0 445 446# Start the AP with beaconing disabled by default. 447#start_disabled=0 448 449# Client isolation can be used to prevent low-level bridging of frames between 450# associated stations in the BSS. By default, this bridging is allowed. 451#ap_isolate=1 452 453# Fixed BSS Load value for testing purposes 454# This field can be used to configure hostapd to add a fixed BSS Load element 455# into Beacon and Probe Response frames for testing purposes. The format is 456# <station count>:<channel utilization>:<available admission capacity> 457#bss_load_test=12:80:20000 458 459##### IEEE 802.11n related configuration ###################################### 460 461# ieee80211n: Whether IEEE 802.11n (HT) is enabled 462# 0 = disabled (default) 463# 1 = enabled 464# Note: You will also need to enable WMM for full HT functionality. 465ieee80211n=1 466 467# ht_capab: HT capabilities (list of flags) 468# LDPC coding capability: [LDPC] = supported 469# Supported channel width set: [HT40-] = both 20 MHz and 40 MHz with secondary 470# channel below the primary channel; [HT40+] = both 20 MHz and 40 MHz 471# with secondary channel above the primary channel 472# (20 MHz only if neither is set) 473# Note: There are limits on which channels can be used with HT40- and 474# HT40+. Following table shows the channels that may be available for 475# HT40- and HT40+ use per IEEE 802.11n Annex J: 476# freq HT40- HT40+ 477# 2.4 GHz 5-13 1-7 (1-9 in Europe/Japan) 478# 5 GHz 40,48,56,64 36,44,52,60 479# (depending on the location, not all of these channels may be available 480# for use) 481# Please note that 40 MHz channels may switch their primary and secondary 482# channels if needed or creation of 40 MHz channel maybe rejected based 483# on overlapping BSSes. These changes are done automatically when hostapd 484# is setting up the 40 MHz channel. 485# Spatial Multiplexing (SM) Power Save: [SMPS-STATIC] or [SMPS-DYNAMIC] 486# (SMPS disabled if neither is set) 487# HT-greenfield: [GF] (disabled if not set) 488# Short GI for 20 MHz: [SHORT-GI-20] (disabled if not set) 489# Short GI for 40 MHz: [SHORT-GI-40] (disabled if not set) 490# Tx STBC: [TX-STBC] (disabled if not set) 491# Rx STBC: [RX-STBC1] (one spatial stream), [RX-STBC12] (one or two spatial 492# streams), or [RX-STBC123] (one, two, or three spatial streams); Rx STBC 493# disabled if none of these set 494# HT-delayed Block Ack: [DELAYED-BA] (disabled if not set) 495# Maximum A-MSDU length: [MAX-AMSDU-7935] for 7935 octets (3839 octets if not 496# set) 497# DSSS/CCK Mode in 40 MHz: [DSSS_CCK-40] = allowed (not allowed if not set) 498# 40 MHz intolerant [40-INTOLERANT] (not advertised if not set) 499# L-SIG TXOP protection support: [LSIG-TXOP-PROT] (disabled if not set) 500ht_capab=[HT40-][DSSS_CCK-40][SHORT-GI-40] 501 502# Require stations to support HT PHY (reject association if they do not) 503#require_ht=1 504 505# If set non-zero, require stations to perform scans of overlapping 506# channels to test for stations which would be affected by 40 MHz traffic. 507# This parameter sets the interval in seconds between these scans. This 508# is useful only for testing that stations properly set the OBSS interval, 509# since the other parameters in the OBSS scan parameters IE are set to 0. 510#obss_interval=0 511 512##### IEEE 802.11ac related configuration ##################################### 513 514# ieee80211ac: Whether IEEE 802.11ac (VHT) is enabled 515# 0 = disabled (default) 516# 1 = enabled 517# Note: You will also need to enable WMM for full VHT functionality. 518#ieee80211ac=1 519 520# vht_capab: VHT capabilities (list of flags) 521# 522# vht_max_mpdu_len: [MAX-MPDU-7991] [MAX-MPDU-11454] 523# Indicates maximum MPDU length 524# 0 = 3895 octets (default) 525# 1 = 7991 octets 526# 2 = 11454 octets 527# 3 = reserved 528# 529# supported_chan_width: [VHT160] [VHT160-80PLUS80] 530# Indicates supported Channel widths 531# 0 = 160 MHz & 80+80 channel widths are not supported (default) 532# 1 = 160 MHz channel width is supported 533# 2 = 160 MHz & 80+80 channel widths are supported 534# 3 = reserved 535# 536# Rx LDPC coding capability: [RXLDPC] 537# Indicates support for receiving LDPC coded pkts 538# 0 = Not supported (default) 539# 1 = Supported 540# 541# Short GI for 80 MHz: [SHORT-GI-80] 542# Indicates short GI support for reception of packets transmitted with TXVECTOR 543# params format equal to VHT and CBW = 80Mhz 544# 0 = Not supported (default) 545# 1 = Supported 546# 547# Short GI for 160 MHz: [SHORT-GI-160] 548# Indicates short GI support for reception of packets transmitted with TXVECTOR 549# params format equal to VHT and CBW = 160Mhz 550# 0 = Not supported (default) 551# 1 = Supported 552# 553# Tx STBC: [TX-STBC-2BY1] 554# Indicates support for the transmission of at least 2x1 STBC 555# 0 = Not supported (default) 556# 1 = Supported 557# 558# Rx STBC: [RX-STBC-1] [RX-STBC-12] [RX-STBC-123] [RX-STBC-1234] 559# Indicates support for the reception of PPDUs using STBC 560# 0 = Not supported (default) 561# 1 = support of one spatial stream 562# 2 = support of one and two spatial streams 563# 3 = support of one, two and three spatial streams 564# 4 = support of one, two, three and four spatial streams 565# 5,6,7 = reserved 566# 567# SU Beamformer Capable: [SU-BEAMFORMER] 568# Indicates support for operation as a single user beamformer 569# 0 = Not supported (default) 570# 1 = Supported 571# 572# SU Beamformee Capable: [SU-BEAMFORMEE] 573# Indicates support for operation as a single user beamformee 574# 0 = Not supported (default) 575# 1 = Supported 576# 577# Compressed Steering Number of Beamformer Antennas Supported: [BF-ANTENNA-2] 578# Beamformee's capability indicating the maximum number of beamformer 579# antennas the beamformee can support when sending compressed beamforming 580# feedback 581# If SU beamformer capable, set to maximum value minus 1 582# else reserved (default) 583# 584# Number of Sounding Dimensions: [SOUNDING-DIMENSION-2] 585# Beamformer's capability indicating the maximum value of the NUM_STS parameter 586# in the TXVECTOR of a VHT NDP 587# If SU beamformer capable, set to maximum value minus 1 588# else reserved (default) 589# 590# MU Beamformer Capable: [MU-BEAMFORMER] 591# Indicates support for operation as an MU beamformer 592# 0 = Not supported or sent by Non-AP STA (default) 593# 1 = Supported 594# 595# MU Beamformee Capable: [MU-BEAMFORMEE] 596# Indicates support for operation as an MU beamformee 597# 0 = Not supported or sent by AP (default) 598# 1 = Supported 599# 600# VHT TXOP PS: [VHT-TXOP-PS] 601# Indicates whether or not the AP supports VHT TXOP Power Save Mode 602# or whether or not the STA is in VHT TXOP Power Save mode 603# 0 = VHT AP doesnt support VHT TXOP PS mode (OR) VHT Sta not in VHT TXOP PS 604# mode 605# 1 = VHT AP supports VHT TXOP PS mode (OR) VHT Sta is in VHT TXOP power save 606# mode 607# 608# +HTC-VHT Capable: [HTC-VHT] 609# Indicates whether or not the STA supports receiving a VHT variant HT Control 610# field. 611# 0 = Not supported (default) 612# 1 = supported 613# 614# Maximum A-MPDU Length Exponent: [MAX-A-MPDU-LEN-EXP0]..[MAX-A-MPDU-LEN-EXP7] 615# Indicates the maximum length of A-MPDU pre-EOF padding that the STA can recv 616# This field is an integer in the range of 0 to 7. 617# The length defined by this field is equal to 618# 2 pow(13 + Maximum A-MPDU Length Exponent) -1 octets 619# 620# VHT Link Adaptation Capable: [VHT-LINK-ADAPT2] [VHT-LINK-ADAPT3] 621# Indicates whether or not the STA supports link adaptation using VHT variant 622# HT Control field 623# If +HTC-VHTcapable is 1 624# 0 = (no feedback) if the STA does not provide VHT MFB (default) 625# 1 = reserved 626# 2 = (Unsolicited) if the STA provides only unsolicited VHT MFB 627# 3 = (Both) if the STA can provide VHT MFB in response to VHT MRQ and if the 628# STA provides unsolicited VHT MFB 629# Reserved if +HTC-VHTcapable is 0 630# 631# Rx Antenna Pattern Consistency: [RX-ANTENNA-PATTERN] 632# Indicates the possibility of Rx antenna pattern change 633# 0 = Rx antenna pattern might change during the lifetime of an association 634# 1 = Rx antenna pattern does not change during the lifetime of an association 635# 636# Tx Antenna Pattern Consistency: [TX-ANTENNA-PATTERN] 637# Indicates the possibility of Tx antenna pattern change 638# 0 = Tx antenna pattern might change during the lifetime of an association 639# 1 = Tx antenna pattern does not change during the lifetime of an association 640#vht_capab=[SHORT-GI-80][HTC-VHT] 641# 642# Require stations to support VHT PHY (reject association if they do not) 643#require_vht=1 644 645# 0 = 20 or 40 MHz operating Channel width 646# 1 = 80 MHz channel width 647# 2 = 160 MHz channel width 648# 3 = 80+80 MHz channel width 649#vht_oper_chwidth=1 650# 651# center freq = 5 GHz + (5 * index) 652# So index 42 gives center freq 5.210 GHz 653# which is channel 42 in 5G band 654# 655#vht_oper_centr_freq_seg0_idx=42 656# 657# center freq = 5 GHz + (5 * index) 658# So index 159 gives center freq 5.795 GHz 659# which is channel 159 in 5G band 660# 661#vht_oper_centr_freq_seg1_idx=159 662 663##### IEEE 802.1X-2004 related configuration ################################## 664 665# Require IEEE 802.1X authorization 666#ieee8021x=1 667 668# IEEE 802.1X/EAPOL version 669# hostapd is implemented based on IEEE Std 802.1X-2004 which defines EAPOL 670# version 2. However, there are many client implementations that do not handle 671# the new version number correctly (they seem to drop the frames completely). 672# In order to make hostapd interoperate with these clients, the version number 673# can be set to the older version (1) with this configuration value. 674#eapol_version=2 675 676# Optional displayable message sent with EAP Request-Identity. The first \0 677# in this string will be converted to ASCII-0 (nul). This can be used to 678# separate network info (comma separated list of attribute=value pairs); see, 679# e.g., RFC 4284. 680#eap_message=hello 681#eap_message=hello\0networkid=netw,nasid=foo,portid=0,NAIRealms=example.com 682 683# WEP rekeying (disabled if key lengths are not set or are set to 0) 684# Key lengths for default/broadcast and individual/unicast keys: 685# 5 = 40-bit WEP (also known as 64-bit WEP with 40 secret bits) 686# 13 = 104-bit WEP (also known as 128-bit WEP with 104 secret bits) 687#wep_key_len_broadcast=5 688#wep_key_len_unicast=5 689# Rekeying period in seconds. 0 = do not rekey (i.e., set keys only once) 690#wep_rekey_period=300 691 692# EAPOL-Key index workaround (set bit7) for WinXP Supplicant (needed only if 693# only broadcast keys are used) 694eapol_key_index_workaround=0 695 696# EAP reauthentication period in seconds (default: 3600 seconds; 0 = disable 697# reauthentication). 698#eap_reauth_period=3600 699 700# Use PAE group address (01:80:c2:00:00:03) instead of individual target 701# address when sending EAPOL frames with driver=wired. This is the most common 702# mechanism used in wired authentication, but it also requires that the port 703# is only used by one station. 704#use_pae_group_addr=1 705 706##### Integrated EAP server ################################################### 707 708# Optionally, hostapd can be configured to use an integrated EAP server 709# to process EAP authentication locally without need for an external RADIUS 710# server. This functionality can be used both as a local authentication server 711# for IEEE 802.1X/EAPOL and as a RADIUS server for other devices. 712 713# Use integrated EAP server instead of external RADIUS authentication 714# server. This is also needed if hostapd is configured to act as a RADIUS 715# authentication server. 716eap_server=0 717 718# Path for EAP server user database 719# If SQLite support is included, this can be set to "sqlite:/path/to/sqlite.db" 720# to use SQLite database instead of a text file. 721#eap_user_file=/etc/hostapd.eap_user 722 723# CA certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS 724#ca_cert=/etc/hostapd.ca.pem 725 726# Server certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS 727#server_cert=/etc/hostapd.server.pem 728 729# Private key matching with the server certificate for EAP-TLS/PEAP/TTLS 730# This may point to the same file as server_cert if both certificate and key 731# are included in a single file. PKCS#12 (PFX) file (.p12/.pfx) can also be 732# used by commenting out server_cert and specifying the PFX file as the 733# private_key. 734#private_key=/etc/hostapd.server.prv 735 736# Passphrase for private key 737#private_key_passwd=secret passphrase 738 739# Server identity 740# EAP methods that provide mechanism for authenticated server identity delivery 741# use this value. If not set, "hostapd" is used as a default. 742#server_id=server.example.com 743 744# Enable CRL verification. 745# Note: hostapd does not yet support CRL downloading based on CDP. Thus, a 746# valid CRL signed by the CA is required to be included in the ca_cert file. 747# This can be done by using PEM format for CA certificate and CRL and 748# concatenating these into one file. Whenever CRL changes, hostapd needs to be 749# restarted to take the new CRL into use. 750# 0 = do not verify CRLs (default) 751# 1 = check the CRL of the user certificate 752# 2 = check all CRLs in the certificate path 753#check_crl=1 754 755# Cached OCSP stapling response (DER encoded) 756# If set, this file is sent as a certificate status response by the EAP server 757# if the EAP peer requests certificate status in the ClientHello message. 758# This cache file can be updated, e.g., by running following command 759# periodically to get an update from the OCSP responder: 760# openssl ocsp \ 761# -no_nonce \ 762# -CAfile /etc/hostapd.ca.pem \ 763# -issuer /etc/hostapd.ca.pem \ 764# -cert /etc/hostapd.server.pem \ 765# -url http://ocsp.example.com:8888/ \ 766# -respout /tmp/ocsp-cache.der 767#ocsp_stapling_response=/tmp/ocsp-cache.der 768 769# dh_file: File path to DH/DSA parameters file (in PEM format) 770# This is an optional configuration file for setting parameters for an 771# ephemeral DH key exchange. In most cases, the default RSA authentication does 772# not use this configuration. However, it is possible setup RSA to use 773# ephemeral DH key exchange. In addition, ciphers with DSA keys always use 774# ephemeral DH keys. This can be used to achieve forward secrecy. If the file 775# is in DSA parameters format, it will be automatically converted into DH 776# params. This parameter is required if anonymous EAP-FAST is used. 777# You can generate DH parameters file with OpenSSL, e.g., 778# "openssl dhparam -out /etc/hostapd.dh.pem 1024" 779#dh_file=/etc/hostapd.dh.pem 780 781# Fragment size for EAP methods 782#fragment_size=1400 783 784# Finite cyclic group for EAP-pwd. Number maps to group of domain parameters 785# using the IANA repository for IKE (RFC 2409). 786#pwd_group=19 787 788# Configuration data for EAP-SIM database/authentication gateway interface. 789# This is a text string in implementation specific format. The example 790# implementation in eap_sim_db.c uses this as the UNIX domain socket name for 791# the HLR/AuC gateway (e.g., hlr_auc_gw). In this case, the path uses "unix:" 792# prefix. If hostapd is built with SQLite support (CONFIG_SQLITE=y in .config), 793# database file can be described with an optional db=<path> parameter. 794#eap_sim_db=unix:/tmp/hlr_auc_gw.sock 795#eap_sim_db=unix:/tmp/hlr_auc_gw.sock db=/tmp/hostapd.db 796 797# Encryption key for EAP-FAST PAC-Opaque values. This key must be a secret, 798# random value. It is configured as a 16-octet value in hex format. It can be 799# generated, e.g., with the following command: 800# od -tx1 -v -N16 /dev/random | colrm 1 8 | tr -d ' ' 801#pac_opaque_encr_key=000102030405060708090a0b0c0d0e0f 802 803# EAP-FAST authority identity (A-ID) 804# A-ID indicates the identity of the authority that issues PACs. The A-ID 805# should be unique across all issuing servers. In theory, this is a variable 806# length field, but due to some existing implementations requiring A-ID to be 807# 16 octets in length, it is strongly recommended to use that length for the 808# field to provid interoperability with deployed peer implementations. This 809# field is configured in hex format. 810#eap_fast_a_id=101112131415161718191a1b1c1d1e1f 811 812# EAP-FAST authority identifier information (A-ID-Info) 813# This is a user-friendly name for the A-ID. For example, the enterprise name 814# and server name in a human-readable format. This field is encoded as UTF-8. 815#eap_fast_a_id_info=test server 816 817# Enable/disable different EAP-FAST provisioning modes: 818#0 = provisioning disabled 819#1 = only anonymous provisioning allowed 820#2 = only authenticated provisioning allowed 821#3 = both provisioning modes allowed (default) 822#eap_fast_prov=3 823 824# EAP-FAST PAC-Key lifetime in seconds (hard limit) 825#pac_key_lifetime=604800 826 827# EAP-FAST PAC-Key refresh time in seconds (soft limit on remaining hard 828# limit). The server will generate a new PAC-Key when this number of seconds 829# (or fewer) of the lifetime remains. 830#pac_key_refresh_time=86400 831 832# EAP-SIM and EAP-AKA protected success/failure indication using AT_RESULT_IND 833# (default: 0 = disabled). 834#eap_sim_aka_result_ind=1 835 836# Trusted Network Connect (TNC) 837# If enabled, TNC validation will be required before the peer is allowed to 838# connect. Note: This is only used with EAP-TTLS and EAP-FAST. If any other 839# EAP method is enabled, the peer will be allowed to connect without TNC. 840#tnc=1 841 842 843##### IEEE 802.11f - Inter-Access Point Protocol (IAPP) ####################### 844 845# Interface to be used for IAPP broadcast packets 846#iapp_interface=eth0 847 848 849##### RADIUS client configuration ############################################# 850# for IEEE 802.1X with external Authentication Server, IEEE 802.11 851# authentication with external ACL for MAC addresses, and accounting 852 853# The own IP address of the access point (used as NAS-IP-Address) 854own_ip_addr=192.168.100.1 855 856# Optional NAS-Identifier string for RADIUS messages. When used, this should be 857# a unique to the NAS within the scope of the RADIUS server. For example, a 858# fully qualified domain name can be used here. 859# When using IEEE 802.11r, nas_identifier must be set and must be between 1 and 860# 48 octets long. 861#nas_identifier=ap.example.com 862 863# RADIUS authentication server 864#auth_server_addr=127.0.0.1 865#auth_server_port=1812 866#auth_server_shared_secret=secret 867 868# RADIUS accounting server 869#acct_server_addr=127.0.0.1 870#acct_server_port=1813 871#acct_server_shared_secret=secret 872 873# Secondary RADIUS servers; to be used if primary one does not reply to 874# RADIUS packets. These are optional and there can be more than one secondary 875# server listed. 876#auth_server_addr=127.0.0.2 877#auth_server_port=1812 878#auth_server_shared_secret=secret2 879# 880#acct_server_addr=127.0.0.2 881#acct_server_port=1813 882#acct_server_shared_secret=secret2 883 884# Retry interval for trying to return to the primary RADIUS server (in 885# seconds). RADIUS client code will automatically try to use the next server 886# when the current server is not replying to requests. If this interval is set, 887# primary server will be retried after configured amount of time even if the 888# currently used secondary server is still working. 889#radius_retry_primary_interval=600 890 891 892# Interim accounting update interval 893# If this is set (larger than 0) and acct_server is configured, hostapd will 894# send interim accounting updates every N seconds. Note: if set, this overrides 895# possible Acct-Interim-Interval attribute in Access-Accept message. Thus, this 896# value should not be configured in hostapd.conf, if RADIUS server is used to 897# control the interim interval. 898# This value should not be less 600 (10 minutes) and must not be less than 899# 60 (1 minute). 900#radius_acct_interim_interval=600 901 902# Request Chargeable-User-Identity (RFC 4372) 903# This parameter can be used to configure hostapd to request CUI from the 904# RADIUS server by including Chargeable-User-Identity attribute into 905# Access-Request packets. 906#radius_request_cui=1 907 908# Dynamic VLAN mode; allow RADIUS authentication server to decide which VLAN 909# is used for the stations. This information is parsed from following RADIUS 910# attributes based on RFC 3580 and RFC 2868: Tunnel-Type (value 13 = VLAN), 911# Tunnel-Medium-Type (value 6 = IEEE 802), Tunnel-Private-Group-ID (value 912# VLANID as a string). Optionally, the local MAC ACL list (accept_mac_file) can 913# be used to set static client MAC address to VLAN ID mapping. 914# 0 = disabled (default) 915# 1 = option; use default interface if RADIUS server does not include VLAN ID 916# 2 = required; reject authentication if RADIUS server does not include VLAN ID 917#dynamic_vlan=0 918 919# VLAN interface list for dynamic VLAN mode is read from a separate text file. 920# This list is used to map VLAN ID from the RADIUS server to a network 921# interface. Each station is bound to one interface in the same way as with 922# multiple BSSIDs or SSIDs. Each line in this text file is defining a new 923# interface and the line must include VLAN ID and interface name separated by 924# white space (space or tab). 925# If no entries are provided by this file, the station is statically mapped 926# to <bss-iface>.<vlan-id> interfaces. 927#vlan_file=/etc/hostapd.vlan 928 929# Interface where 802.1q tagged packets should appear when a RADIUS server is 930# used to determine which VLAN a station is on. hostapd creates a bridge for 931# each VLAN. Then hostapd adds a VLAN interface (associated with the interface 932# indicated by 'vlan_tagged_interface') and the appropriate wireless interface 933# to the bridge. 934#vlan_tagged_interface=eth0 935 936# Bridge (prefix) to add the wifi and the tagged interface to. This gets the 937# VLAN ID appended. It defaults to brvlan%d if no tagged interface is given 938# and br%s.%d if a tagged interface is given, provided %s = tagged interface 939# and %d = VLAN ID. 940#vlan_bridge=brvlan 941 942# When hostapd creates a VLAN interface on vlan_tagged_interfaces, it needs 943# to know how to name it. 944# 0 = vlan<XXX>, e.g., vlan1 945# 1 = <vlan_tagged_interface>.<XXX>, e.g. eth0.1 946#vlan_naming=0 947 948# Arbitrary RADIUS attributes can be added into Access-Request and 949# Accounting-Request packets by specifying the contents of the attributes with 950# the following configuration parameters. There can be multiple of these to 951# add multiple attributes. These parameters can also be used to override some 952# of the attributes added automatically by hostapd. 953# Format: <attr_id>[:<syntax:value>] 954# attr_id: RADIUS attribute type (e.g., 26 = Vendor-Specific) 955# syntax: s = string (UTF-8), d = integer, x = octet string 956# value: attribute value in format indicated by the syntax 957# If syntax and value parts are omitted, a null value (single 0x00 octet) is 958# used. 959# 960# Additional Access-Request attributes 961# radius_auth_req_attr=<attr_id>[:<syntax:value>] 962# Examples: 963# Operator-Name = "Operator" 964#radius_auth_req_attr=126:s:Operator 965# Service-Type = Framed (2) 966#radius_auth_req_attr=6:d:2 967# Connect-Info = "testing" (this overrides the automatically generated value) 968#radius_auth_req_attr=77:s:testing 969# Same Connect-Info value set as a hexdump 970#radius_auth_req_attr=77:x:74657374696e67 971 972# 973# Additional Accounting-Request attributes 974# radius_acct_req_attr=<attr_id>[:<syntax:value>] 975# Examples: 976# Operator-Name = "Operator" 977#radius_acct_req_attr=126:s:Operator 978 979# Dynamic Authorization Extensions (RFC 5176) 980# This mechanism can be used to allow dynamic changes to user session based on 981# commands from a RADIUS server (or some other disconnect client that has the 982# needed session information). For example, Disconnect message can be used to 983# request an associated station to be disconnected. 984# 985# This is disabled by default. Set radius_das_port to non-zero UDP port 986# number to enable. 987#radius_das_port=3799 988# 989# DAS client (the host that can send Disconnect/CoA requests) and shared secret 990#radius_das_client=192.168.1.123 shared secret here 991# 992# DAS Event-Timestamp time window in seconds 993#radius_das_time_window=300 994# 995# DAS require Event-Timestamp 996#radius_das_require_event_timestamp=1 997 998##### RADIUS authentication server configuration ############################## 999 1000# hostapd can be used as a RADIUS authentication server for other hosts. This 1001# requires that the integrated EAP server is also enabled and both 1002# authentication services are sharing the same configuration. 1003 1004# File name of the RADIUS clients configuration for the RADIUS server. If this 1005# commented out, RADIUS server is disabled. 1006#radius_server_clients=/etc/hostapd.radius_clients 1007 1008# The UDP port number for the RADIUS authentication server 1009#radius_server_auth_port=1812 1010 1011# The UDP port number for the RADIUS accounting server 1012# Commenting this out or setting this to 0 can be used to disable RADIUS 1013# accounting while still enabling RADIUS authentication. 1014#radius_server_acct_port=1813 1015 1016# Use IPv6 with RADIUS server (IPv4 will also be supported using IPv6 API) 1017#radius_server_ipv6=1 1018 1019 1020##### WPA/IEEE 802.11i configuration ########################################## 1021 1022# Enable WPA. Setting this variable configures the AP to require WPA (either 1023# WPA-PSK or WPA-RADIUS/EAP based on other configuration). For WPA-PSK, either 1024# wpa_psk or wpa_passphrase must be set and wpa_key_mgmt must include WPA-PSK. 1025# Instead of wpa_psk / wpa_passphrase, wpa_psk_radius might suffice. 1026# For WPA-RADIUS/EAP, ieee8021x must be set (but without dynamic WEP keys), 1027# RADIUS authentication server must be configured, and WPA-EAP must be included 1028# in wpa_key_mgmt. 1029# This field is a bit field that can be used to enable WPA (IEEE 802.11i/D3.0) 1030# and/or WPA2 (full IEEE 802.11i/RSN): 1031# bit0 = WPA 1032# bit1 = IEEE 802.11i/RSN (WPA2) (dot11RSNAEnabled) 1033#wpa=1 1034 1035# WPA pre-shared keys for WPA-PSK. This can be either entered as a 256-bit 1036# secret in hex format (64 hex digits), wpa_psk, or as an ASCII passphrase 1037# (8..63 characters) that will be converted to PSK. This conversion uses SSID 1038# so the PSK changes when ASCII passphrase is used and the SSID is changed. 1039# wpa_psk (dot11RSNAConfigPSKValue) 1040# wpa_passphrase (dot11RSNAConfigPSKPassPhrase) 1041#wpa_psk=0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef 1042#wpa_passphrase=secret passphrase 1043 1044# Optionally, WPA PSKs can be read from a separate text file (containing list 1045# of (PSK,MAC address) pairs. This allows more than one PSK to be configured. 1046# Use absolute path name to make sure that the files can be read on SIGHUP 1047# configuration reloads. 1048#wpa_psk_file=/etc/hostapd.wpa_psk 1049 1050# Optionally, WPA passphrase can be received from RADIUS authentication server 1051# This requires macaddr_acl to be set to 2 (RADIUS) 1052# 0 = disabled (default) 1053# 1 = optional; use default passphrase/psk if RADIUS server does not include 1054# Tunnel-Password 1055# 2 = required; reject authentication if RADIUS server does not include 1056# Tunnel-Password 1057#wpa_psk_radius=0 1058 1059# Set of accepted key management algorithms (WPA-PSK, WPA-EAP, or both). The 1060# entries are separated with a space. WPA-PSK-SHA256 and WPA-EAP-SHA256 can be 1061# added to enable SHA256-based stronger algorithms. 1062# (dot11RSNAConfigAuthenticationSuitesTable) 1063#wpa_key_mgmt=WPA-PSK WPA-EAP 1064 1065# Set of accepted cipher suites (encryption algorithms) for pairwise keys 1066# (unicast packets). This is a space separated list of algorithms: 1067# CCMP = AES in Counter mode with CBC-MAC [RFC 3610, IEEE 802.11i/D7.0] 1068# TKIP = Temporal Key Integrity Protocol [IEEE 802.11i/D7.0] 1069# Group cipher suite (encryption algorithm for broadcast and multicast frames) 1070# is automatically selected based on this configuration. If only CCMP is 1071# allowed as the pairwise cipher, group cipher will also be CCMP. Otherwise, 1072# TKIP will be used as the group cipher. 1073# (dot11RSNAConfigPairwiseCiphersTable) 1074# Pairwise cipher for WPA (v1) (default: TKIP) 1075#wpa_pairwise=TKIP CCMP 1076# Pairwise cipher for RSN/WPA2 (default: use wpa_pairwise value) 1077#rsn_pairwise=CCMP 1078 1079# Time interval for rekeying GTK (broadcast/multicast encryption keys) in 1080# seconds. (dot11RSNAConfigGroupRekeyTime) 1081#wpa_group_rekey=600 1082 1083# Rekey GTK when any STA that possesses the current GTK is leaving the BSS. 1084# (dot11RSNAConfigGroupRekeyStrict) 1085#wpa_strict_rekey=1 1086 1087# Time interval for rekeying GMK (master key used internally to generate GTKs 1088# (in seconds). 1089#wpa_gmk_rekey=86400 1090 1091# Maximum lifetime for PTK in seconds. This can be used to enforce rekeying of 1092# PTK to mitigate some attacks against TKIP deficiencies. 1093#wpa_ptk_rekey=600 1094 1095# Enable IEEE 802.11i/RSN/WPA2 pre-authentication. This is used to speed up 1096# roaming be pre-authenticating IEEE 802.1X/EAP part of the full RSN 1097# authentication and key handshake before actually associating with a new AP. 1098# (dot11RSNAPreauthenticationEnabled) 1099#rsn_preauth=1 1100# 1101# Space separated list of interfaces from which pre-authentication frames are 1102# accepted (e.g., 'eth0' or 'eth0 wlan0wds0'. This list should include all 1103# interface that are used for connections to other APs. This could include 1104# wired interfaces and WDS links. The normal wireless data interface towards 1105# associated stations (e.g., wlan0) should not be added, since 1106# pre-authentication is only used with APs other than the currently associated 1107# one. 1108#rsn_preauth_interfaces=eth0 1109 1110# peerkey: Whether PeerKey negotiation for direct links (IEEE 802.11e) is 1111# allowed. This is only used with RSN/WPA2. 1112# 0 = disabled (default) 1113# 1 = enabled 1114#peerkey=1 1115 1116# ieee80211w: Whether management frame protection (MFP) is enabled 1117# 0 = disabled (default) 1118# 1 = optional 1119# 2 = required 1120#ieee80211w=0 1121 1122# Group management cipher suite 1123# Default: AES-128-CMAC (BIP) 1124# Other options (depending on driver support): 1125# BIP-GMAC-128 1126# BIP-GMAC-256 1127# BIP-CMAC-256 1128# Note: All the stations connecting to the BSS will also need to support the 1129# selected cipher. The default AES-128-CMAC is the only option that is commonly 1130# available in deployed devices. 1131#group_mgmt_cipher=AES-128-CMAC 1132 1133# Association SA Query maximum timeout (in TU = 1.024 ms; for MFP) 1134# (maximum time to wait for a SA Query response) 1135# dot11AssociationSAQueryMaximumTimeout, 1...4294967295 1136#assoc_sa_query_max_timeout=1000 1137 1138# Association SA Query retry timeout (in TU = 1.024 ms; for MFP) 1139# (time between two subsequent SA Query requests) 1140# dot11AssociationSAQueryRetryTimeout, 1...4294967295 1141#assoc_sa_query_retry_timeout=201 1142 1143# disable_pmksa_caching: Disable PMKSA caching 1144# This parameter can be used to disable caching of PMKSA created through EAP 1145# authentication. RSN preauthentication may still end up using PMKSA caching if 1146# it is enabled (rsn_preauth=1). 1147# 0 = PMKSA caching enabled (default) 1148# 1 = PMKSA caching disabled 1149#disable_pmksa_caching=0 1150 1151# okc: Opportunistic Key Caching (aka Proactive Key Caching) 1152# Allow PMK cache to be shared opportunistically among configured interfaces 1153# and BSSes (i.e., all configurations within a single hostapd process). 1154# 0 = disabled (default) 1155# 1 = enabled 1156#okc=1 1157 1158# SAE threshold for anti-clogging mechanism (dot11RSNASAEAntiCloggingThreshold) 1159# This parameter defines how many open SAE instances can be in progress at the 1160# same time before the anti-clogging mechanism is taken into use. 1161#sae_anti_clogging_threshold=5 1162 1163# Enabled SAE finite cyclic groups 1164# SAE implementation are required to support group 19 (ECC group defined over a 1165# 256-bit prime order field). All groups that are supported by the 1166# implementation are enabled by default. This configuration parameter can be 1167# used to specify a limited set of allowed groups. The group values are listed 1168# in the IANA registry: 1169# http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-9 1170#sae_groups=19 20 21 25 26 1171 1172##### IEEE 802.11r configuration ############################################## 1173 1174# Mobility Domain identifier (dot11FTMobilityDomainID, MDID) 1175# MDID is used to indicate a group of APs (within an ESS, i.e., sharing the 1176# same SSID) between which a STA can use Fast BSS Transition. 1177# 2-octet identifier as a hex string. 1178#mobility_domain=a1b2 1179 1180# PMK-R0 Key Holder identifier (dot11FTR0KeyHolderID) 1181# 1 to 48 octet identifier. 1182# This is configured with nas_identifier (see RADIUS client section above). 1183 1184# Default lifetime of the PMK-RO in minutes; range 1..65535 1185# (dot11FTR0KeyLifetime) 1186#r0_key_lifetime=10000 1187 1188# PMK-R1 Key Holder identifier (dot11FTR1KeyHolderID) 1189# 6-octet identifier as a hex string. 1190#r1_key_holder=000102030405 1191 1192# Reassociation deadline in time units (TUs / 1.024 ms; range 1000..65535) 1193# (dot11FTReassociationDeadline) 1194#reassociation_deadline=1000 1195 1196# List of R0KHs in the same Mobility Domain 1197# format: <MAC address> <NAS Identifier> <128-bit key as hex string> 1198# This list is used to map R0KH-ID (NAS Identifier) to a destination MAC 1199# address when requesting PMK-R1 key from the R0KH that the STA used during the 1200# Initial Mobility Domain Association. 1201#r0kh=02:01:02:03:04:05 r0kh-1.example.com 000102030405060708090a0b0c0d0e0f 1202#r0kh=02:01:02:03:04:06 r0kh-2.example.com 00112233445566778899aabbccddeeff 1203# And so on.. One line per R0KH. 1204 1205# List of R1KHs in the same Mobility Domain 1206# format: <MAC address> <R1KH-ID> <128-bit key as hex string> 1207# This list is used to map R1KH-ID to a destination MAC address when sending 1208# PMK-R1 key from the R0KH. This is also the list of authorized R1KHs in the MD 1209# that can request PMK-R1 keys. 1210#r1kh=02:01:02:03:04:05 02:11:22:33:44:55 000102030405060708090a0b0c0d0e0f 1211#r1kh=02:01:02:03:04:06 02:11:22:33:44:66 00112233445566778899aabbccddeeff 1212# And so on.. One line per R1KH. 1213 1214# Whether PMK-R1 push is enabled at R0KH 1215# 0 = do not push PMK-R1 to all configured R1KHs (default) 1216# 1 = push PMK-R1 to all configured R1KHs whenever a new PMK-R0 is derived 1217#pmk_r1_push=1 1218 1219##### Neighbor table ########################################################## 1220# Maximum number of entries kept in AP table (either for neigbor table or for 1221# detecting Overlapping Legacy BSS Condition). The oldest entry will be 1222# removed when adding a new entry that would make the list grow over this 1223# limit. Note! WFA certification for IEEE 802.11g requires that OLBC is 1224# enabled, so this field should not be set to 0 when using IEEE 802.11g. 1225# default: 255 1226#ap_table_max_size=255 1227 1228# Number of seconds of no frames received after which entries may be deleted 1229# from the AP table. Since passive scanning is not usually performed frequently 1230# this should not be set to very small value. In addition, there is no 1231# guarantee that every scan cycle will receive beacon frames from the 1232# neighboring APs. 1233# default: 60 1234#ap_table_expiration_time=3600 1235 1236 1237##### Wi-Fi Protected Setup (WPS) ############################################# 1238 1239# WPS state 1240# 0 = WPS disabled (default) 1241# 1 = WPS enabled, not configured 1242# 2 = WPS enabled, configured 1243#wps_state=2 1244 1245# Whether to manage this interface independently from other WPS interfaces 1246# By default, a single hostapd process applies WPS operations to all configured 1247# interfaces. This parameter can be used to disable that behavior for a subset 1248# of interfaces. If this is set to non-zero for an interface, WPS commands 1249# issued on that interface do not apply to other interfaces and WPS operations 1250# performed on other interfaces do not affect this interface. 1251#wps_independent=0 1252 1253# AP can be configured into a locked state where new WPS Registrar are not 1254# accepted, but previously authorized Registrars (including the internal one) 1255# can continue to add new Enrollees. 1256#ap_setup_locked=1 1257 1258# Universally Unique IDentifier (UUID; see RFC 4122) of the device 1259# This value is used as the UUID for the internal WPS Registrar. If the AP 1260# is also using UPnP, this value should be set to the device's UPnP UUID. 1261# If not configured, UUID will be generated based on the local MAC address. 1262#uuid=12345678-9abc-def0-1234-56789abcdef0 1263 1264# Note: If wpa_psk_file is set, WPS is used to generate random, per-device PSKs 1265# that will be appended to the wpa_psk_file. If wpa_psk_file is not set, the 1266# default PSK (wpa_psk/wpa_passphrase) will be delivered to Enrollees. Use of 1267# per-device PSKs is recommended as the more secure option (i.e., make sure to 1268# set wpa_psk_file when using WPS with WPA-PSK). 1269 1270# When an Enrollee requests access to the network with PIN method, the Enrollee 1271# PIN will need to be entered for the Registrar. PIN request notifications are 1272# sent to hostapd ctrl_iface monitor. In addition, they can be written to a 1273# text file that could be used, e.g., to populate the AP administration UI with 1274# pending PIN requests. If the following variable is set, the PIN requests will 1275# be written to the configured file. 1276#wps_pin_requests=/var/run/hostapd_wps_pin_requests 1277 1278# Device Name 1279# User-friendly description of device; up to 32 octets encoded in UTF-8 1280#device_name=Wireless AP 1281 1282# Manufacturer 1283# The manufacturer of the device (up to 64 ASCII characters) 1284#manufacturer=Company 1285 1286# Model Name 1287# Model of the device (up to 32 ASCII characters) 1288#model_name=WAP 1289 1290# Model Number 1291# Additional device description (up to 32 ASCII characters) 1292#model_number=123 1293 1294# Serial Number 1295# Serial number of the device (up to 32 characters) 1296#serial_number=12345 1297 1298# Primary Device Type 1299# Used format: <categ>-<OUI>-<subcateg> 1300# categ = Category as an integer value 1301# OUI = OUI and type octet as a 4-octet hex-encoded value; 0050F204 for 1302# default WPS OUI 1303# subcateg = OUI-specific Sub Category as an integer value 1304# Examples: 1305# 1-0050F204-1 (Computer / PC) 1306# 1-0050F204-2 (Computer / Server) 1307# 5-0050F204-1 (Storage / NAS) 1308# 6-0050F204-1 (Network Infrastructure / AP) 1309#device_type=6-0050F204-1 1310 1311# OS Version 1312# 4-octet operating system version number (hex string) 1313#os_version=01020300 1314 1315# Config Methods 1316# List of the supported configuration methods 1317# Available methods: usba ethernet label display ext_nfc_token int_nfc_token 1318# nfc_interface push_button keypad virtual_display physical_display 1319# virtual_push_button physical_push_button 1320#config_methods=label virtual_display virtual_push_button keypad 1321 1322# WPS capability discovery workaround for PBC with Windows 7 1323# Windows 7 uses incorrect way of figuring out AP's WPS capabilities by acting 1324# as a Registrar and using M1 from the AP. The config methods attribute in that 1325# message is supposed to indicate only the configuration method supported by 1326# the AP in Enrollee role, i.e., to add an external Registrar. For that case, 1327# PBC shall not be used and as such, the PushButton config method is removed 1328# from M1 by default. If pbc_in_m1=1 is included in the configuration file, 1329# the PushButton config method is left in M1 (if included in config_methods 1330# parameter) to allow Windows 7 to use PBC instead of PIN (e.g., from a label 1331# in the AP). 1332#pbc_in_m1=1 1333 1334# Static access point PIN for initial configuration and adding Registrars 1335# If not set, hostapd will not allow external WPS Registrars to control the 1336# access point. The AP PIN can also be set at runtime with hostapd_cli 1337# wps_ap_pin command. Use of temporary (enabled by user action) and random 1338# AP PIN is much more secure than configuring a static AP PIN here. As such, 1339# use of the ap_pin parameter is not recommended if the AP device has means for 1340# displaying a random PIN. 1341#ap_pin=12345670 1342 1343# Skip building of automatic WPS credential 1344# This can be used to allow the automatically generated Credential attribute to 1345# be replaced with pre-configured Credential(s). 1346#skip_cred_build=1 1347 1348# Additional Credential attribute(s) 1349# This option can be used to add pre-configured Credential attributes into M8 1350# message when acting as a Registrar. If skip_cred_build=1, this data will also 1351# be able to override the Credential attribute that would have otherwise been 1352# automatically generated based on network configuration. This configuration 1353# option points to an external file that much contain the WPS Credential 1354# attribute(s) as binary data. 1355#extra_cred=hostapd.cred 1356 1357# Credential processing 1358# 0 = process received credentials internally (default) 1359# 1 = do not process received credentials; just pass them over ctrl_iface to 1360# external program(s) 1361# 2 = process received credentials internally and pass them over ctrl_iface 1362# to external program(s) 1363# Note: With wps_cred_processing=1, skip_cred_build should be set to 1 and 1364# extra_cred be used to provide the Credential data for Enrollees. 1365# 1366# wps_cred_processing=1 will disabled automatic updates of hostapd.conf file 1367# both for Credential processing and for marking AP Setup Locked based on 1368# validation failures of AP PIN. An external program is responsible on updating 1369# the configuration appropriately in this case. 1370#wps_cred_processing=0 1371 1372# AP Settings Attributes for M7 1373# By default, hostapd generates the AP Settings Attributes for M7 based on the 1374# current configuration. It is possible to override this by providing a file 1375# with pre-configured attributes. This is similar to extra_cred file format, 1376# but the AP Settings attributes are not encapsulated in a Credential 1377# attribute. 1378#ap_settings=hostapd.ap_settings 1379 1380# WPS UPnP interface 1381# If set, support for external Registrars is enabled. 1382#upnp_iface=br0 1383 1384# Friendly Name (required for UPnP) 1385# Short description for end use. Should be less than 64 characters. 1386#friendly_name=WPS Access Point 1387 1388# Manufacturer URL (optional for UPnP) 1389#manufacturer_url=http://www.example.com/ 1390 1391# Model Description (recommended for UPnP) 1392# Long description for end user. Should be less than 128 characters. 1393#model_description=Wireless Access Point 1394 1395# Model URL (optional for UPnP) 1396#model_url=http://www.example.com/model/ 1397 1398# Universal Product Code (optional for UPnP) 1399# 12-digit, all-numeric code that identifies the consumer package. 1400#upc=123456789012 1401 1402# WPS RF Bands (a = 5G, b = 2.4G, g = 2.4G, ag = dual band) 1403# This value should be set according to RF band(s) supported by the AP if 1404# hw_mode is not set. For dual band dual concurrent devices, this needs to be 1405# set to ag to allow both RF bands to be advertized. 1406#wps_rf_bands=ag 1407 1408# NFC password token for WPS 1409# These parameters can be used to configure a fixed NFC password token for the 1410# AP. This can be generated, e.g., with nfc_pw_token from wpa_supplicant. When 1411# these parameters are used, the AP is assumed to be deployed with a NFC tag 1412# that includes the matching NFC password token (e.g., written based on the 1413# NDEF record from nfc_pw_token). 1414# 1415#wps_nfc_dev_pw_id: Device Password ID (16..65535) 1416#wps_nfc_dh_pubkey: Hexdump of DH Public Key 1417#wps_nfc_dh_privkey: Hexdump of DH Private Key 1418#wps_nfc_dev_pw: Hexdump of Device Password 1419 1420##### Wi-Fi Direct (P2P) ###################################################### 1421 1422# Enable P2P Device management 1423#manage_p2p=1 1424 1425# Allow cross connection 1426#allow_cross_connection=1 1427 1428#### TDLS (IEEE 802.11z-2010) ################################################# 1429 1430# Prohibit use of TDLS in this BSS 1431#tdls_prohibit=1 1432 1433# Prohibit use of TDLS Channel Switching in this BSS 1434#tdls_prohibit_chan_switch=1 1435 1436##### IEEE 802.11v-2011 ####################################################### 1437 1438# Time advertisement 1439# 0 = disabled (default) 1440# 2 = UTC time at which the TSF timer is 0 1441#time_advertisement=2 1442 1443# Local time zone as specified in 8.3 of IEEE Std 1003.1-2004: 1444# stdoffset[dst[offset][,start[/time],end[/time]]] 1445#time_zone=EST5 1446 1447# WNM-Sleep Mode (extended sleep mode for stations) 1448# 0 = disabled (default) 1449# 1 = enabled (allow stations to use WNM-Sleep Mode) 1450#wnm_sleep_mode=1 1451 1452# BSS Transition Management 1453# 0 = disabled (default) 1454# 1 = enabled 1455#bss_transition=1 1456 1457##### IEEE 802.11u-2011 ####################################################### 1458 1459# Enable Interworking service 1460#interworking=1 1461 1462# Access Network Type 1463# 0 = Private network 1464# 1 = Private network with guest access 1465# 2 = Chargeable public network 1466# 3 = Free public network 1467# 4 = Personal device network 1468# 5 = Emergency services only network 1469# 14 = Test or experimental 1470# 15 = Wildcard 1471#access_network_type=0 1472 1473# Whether the network provides connectivity to the Internet 1474# 0 = Unspecified 1475# 1 = Network provides connectivity to the Internet 1476#internet=1 1477 1478# Additional Step Required for Access 1479# Note: This is only used with open network, i.e., ASRA shall ne set to 0 if 1480# RSN is used. 1481#asra=0 1482 1483# Emergency services reachable 1484#esr=0 1485 1486# Unauthenticated emergency service accessible 1487#uesa=0 1488 1489# Venue Info (optional) 1490# The available values are defined in IEEE Std 802.11u-2011, 7.3.1.34. 1491# Example values (group,type): 1492# 0,0 = Unspecified 1493# 1,7 = Convention Center 1494# 1,13 = Coffee Shop 1495# 2,0 = Unspecified Business 1496# 7,1 Private Residence 1497#venue_group=7 1498#venue_type=1 1499 1500# Homogeneous ESS identifier (optional; dot11HESSID) 1501# If set, this shall be identifical to one of the BSSIDs in the homogeneous 1502# ESS and this shall be set to the same value across all BSSs in homogeneous 1503# ESS. 1504#hessid=02:03:04:05:06:07 1505 1506# Roaming Consortium List 1507# Arbitrary number of Roaming Consortium OIs can be configured with each line 1508# adding a new OI to the list. The first three entries are available through 1509# Beacon and Probe Response frames. Any additional entry will be available only 1510# through ANQP queries. Each OI is between 3 and 15 octets and is configured as 1511# a hexstring. 1512#roaming_consortium=021122 1513#roaming_consortium=2233445566 1514 1515# Venue Name information 1516# This parameter can be used to configure one or more Venue Name Duples for 1517# Venue Name ANQP information. Each entry has a two or three character language 1518# code (ISO-639) separated by colon from the venue name string. 1519# Note that venue_group and venue_type have to be set for Venue Name 1520# information to be complete. 1521#venue_name=eng:Example venue 1522#venue_name=fin:Esimerkkipaikka 1523# Alternative format for language:value strings: 1524# (double quoted string, printf-escaped string) 1525#venue_name=P"eng:Example\nvenue" 1526 1527# Network Authentication Type 1528# This parameter indicates what type of network authentication is used in the 1529# network. 1530# format: <network auth type indicator (1-octet hex str)> [redirect URL] 1531# Network Authentication Type Indicator values: 1532# 00 = Acceptance of terms and conditions 1533# 01 = On-line enrollment supported 1534# 02 = http/https redirection 1535# 03 = DNS redirection 1536#network_auth_type=00 1537#network_auth_type=02http://www.example.com/redirect/me/here/ 1538 1539# IP Address Type Availability 1540# format: <1-octet encoded value as hex str> 1541# (ipv4_type & 0x3f) << 2 | (ipv6_type & 0x3) 1542# ipv4_type: 1543# 0 = Address type not available 1544# 1 = Public IPv4 address available 1545# 2 = Port-restricted IPv4 address available 1546# 3 = Single NATed private IPv4 address available 1547# 4 = Double NATed private IPv4 address available 1548# 5 = Port-restricted IPv4 address and single NATed IPv4 address available 1549# 6 = Port-restricted IPv4 address and double NATed IPv4 address available 1550# 7 = Availability of the address type is not known 1551# ipv6_type: 1552# 0 = Address type not available 1553# 1 = Address type available 1554# 2 = Availability of the address type not known 1555#ipaddr_type_availability=14 1556 1557# Domain Name 1558# format: <variable-octet str>[,<variable-octet str>] 1559#domain_name=example.com,another.example.com,yet-another.example.com 1560 1561# 3GPP Cellular Network information 1562# format: <MCC1,MNC1>[;<MCC2,MNC2>][;...] 1563#anqp_3gpp_cell_net=244,91;310,026;234,56 1564 1565# NAI Realm information 1566# One or more realm can be advertised. Each nai_realm line adds a new realm to 1567# the set. These parameters provide information for stations using Interworking 1568# network selection to allow automatic connection to a network based on 1569# credentials. 1570# format: <encoding>,<NAI Realm(s)>[,<EAP Method 1>][,<EAP Method 2>][,...] 1571# encoding: 1572# 0 = Realm formatted in accordance with IETF RFC 4282 1573# 1 = UTF-8 formatted character string that is not formatted in 1574# accordance with IETF RFC 4282 1575# NAI Realm(s): Semi-colon delimited NAI Realm(s) 1576# EAP Method: <EAP Method>[:<[AuthParam1:Val1]>][<[AuthParam2:Val2]>][...] 1577# EAP Method types, see: 1578# http://www.iana.org/assignments/eap-numbers/eap-numbers.xhtml#eap-numbers-4 1579# AuthParam (Table 8-188 in IEEE Std 802.11-2012): 1580# ID 2 = Non-EAP Inner Authentication Type 1581# 1 = PAP, 2 = CHAP, 3 = MSCHAP, 4 = MSCHAPV2 1582# ID 3 = Inner authentication EAP Method Type 1583# ID 5 = Credential Type 1584# 1 = SIM, 2 = USIM, 3 = NFC Secure Element, 4 = Hardware Token, 1585# 5 = Softoken, 6 = Certificate, 7 = username/password, 9 = Anonymous, 1586# 10 = Vendor Specific 1587#nai_realm=0,example.com;example.net 1588# EAP methods EAP-TLS with certificate and EAP-TTLS/MSCHAPv2 with 1589# username/password 1590#nai_realm=0,example.org,13[5:6],21[2:4][5:7] 1591 1592# QoS Map Set configuration 1593# 1594# Comma delimited QoS Map Set in decimal values 1595# (see IEEE Std 802.11-2012, 8.4.2.97) 1596# 1597# format: 1598# [<DSCP Exceptions[DSCP,UP]>,]<UP 0 range[low,high]>,...<UP 7 range[low,high]> 1599# 1600# There can be up to 21 optional DSCP Exceptions which are pairs of DSCP Value 1601# (0..63 or 255) and User Priority (0..7). This is followed by eight DSCP Range 1602# descriptions with DSCP Low Value and DSCP High Value pairs (0..63 or 255) for 1603# each UP starting from 0. If both low and high value are set to 255, the 1604# corresponding UP is not used. 1605# 1606# default: not set 1607#qos_map_set=53,2,22,6,8,15,0,7,255,255,16,31,32,39,255,255,40,47,255,255 1608 1609##### Hotspot 2.0 ############################################################# 1610 1611# Enable Hotspot 2.0 support 1612#hs20=1 1613 1614# Disable Downstream Group-Addressed Forwarding (DGAF) 1615# This can be used to configure a network where no group-addressed frames are 1616# allowed. The AP will not forward any group-address frames to the stations and 1617# random GTKs are issued for each station to prevent associated stations from 1618# forging such frames to other stations in the BSS. 1619#disable_dgaf=1 1620 1621# OSU Server-Only Authenticated L2 Encryption Network 1622#osen=1 1623 1624# ANQP Domain ID (0..65535) 1625# An identifier for a set of APs in an ESS that share the same common ANQP 1626# information. 0 = Some of the ANQP information is unique to this AP (default). 1627#anqp_domain_id=1234 1628 1629# Deauthentication request timeout 1630# If the RADIUS server indicates that the station is not allowed to connect to 1631# the BSS/ESS, the AP can allow the station some time to download a 1632# notification page (URL included in the message). This parameter sets that 1633# timeout in seconds. 1634#hs20_deauth_req_timeout=60 1635 1636# Operator Friendly Name 1637# This parameter can be used to configure one or more Operator Friendly Name 1638# Duples. Each entry has a two or three character language code (ISO-639) 1639# separated by colon from the operator friendly name string. 1640#hs20_oper_friendly_name=eng:Example operator 1641#hs20_oper_friendly_name=fin:Esimerkkioperaattori 1642 1643# Connection Capability 1644# This can be used to advertise what type of IP traffic can be sent through the 1645# hotspot (e.g., due to firewall allowing/blocking protocols/ports). 1646# format: <IP Protocol>:<Port Number>:<Status> 1647# IP Protocol: 1 = ICMP, 6 = TCP, 17 = UDP 1648# Port Number: 0..65535 1649# Status: 0 = Closed, 1 = Open, 2 = Unknown 1650# Each hs20_conn_capab line is added to the list of advertised tuples. 1651#hs20_conn_capab=1:0:2 1652#hs20_conn_capab=6:22:1 1653#hs20_conn_capab=17:5060:0 1654 1655# WAN Metrics 1656# format: <WAN Info>:<DL Speed>:<UL Speed>:<DL Load>:<UL Load>:<LMD> 1657# WAN Info: B0-B1: Link Status, B2: Symmetric Link, B3: At Capabity 1658# (encoded as two hex digits) 1659# Link Status: 1 = Link up, 2 = Link down, 3 = Link in test state 1660# Downlink Speed: Estimate of WAN backhaul link current downlink speed in kbps; 1661# 1..4294967295; 0 = unknown 1662# Uplink Speed: Estimate of WAN backhaul link current uplink speed in kbps 1663# 1..4294967295; 0 = unknown 1664# Downlink Load: Current load of downlink WAN connection (scaled to 255 = 100%) 1665# Uplink Load: Current load of uplink WAN connection (scaled to 255 = 100%) 1666# Load Measurement Duration: Duration for measuring downlink/uplink load in 1667# tenths of a second (1..65535); 0 if load cannot be determined 1668#hs20_wan_metrics=01:8000:1000:80:240:3000 1669 1670# Operating Class Indication 1671# List of operating classes the BSSes in this ESS use. The Global operating 1672# classes in Table E-4 of IEEE Std 802.11-2012 Annex E define the values that 1673# can be used in this. 1674# format: hexdump of operating class octets 1675# for example, operating classes 81 (2.4 GHz channels 1-13) and 115 (5 GHz 1676# channels 36-48): 1677#hs20_operating_class=5173 1678 1679# OSU icons 1680# <Icon Width>:<Icon Height>:<Language code>:<Icon Type>:<Name>:<file path> 1681#hs20_icon=32:32:eng:image/png:icon32:/tmp/icon32.png 1682#hs20_icon=64:64:eng:image/png:icon64:/tmp/icon64.png 1683 1684# OSU SSID (see ssid2 for format description) 1685# This is the SSID used for all OSU connections to all the listed OSU Providers. 1686#osu_ssid="example" 1687 1688# OSU Providers 1689# One or more sets of following parameter. Each OSU provider is started by the 1690# mandatory osu_server_uri item. The other parameters add information for the 1691# last added OSU provider. 1692# 1693#osu_server_uri=https://example.com/osu/ 1694#osu_friendly_name=eng:Example operator 1695#osu_friendly_name=fin:Esimerkkipalveluntarjoaja 1696#osu_nai=anonymous@example.com 1697#osu_method_list=1 0 1698#osu_icon=icon32 1699#osu_icon=icon64 1700#osu_service_desc=eng:Example services 1701#osu_service_desc=fin:Esimerkkipalveluja 1702# 1703#osu_server_uri=... 1704 1705##### TESTING OPTIONS ######################################################### 1706# 1707# The options in this section are only available when the build configuration 1708# option CONFIG_TESTING_OPTIONS is set while compiling hostapd. They allow 1709# testing some scenarios that are otherwise difficult to reproduce. 1710# 1711# Ignore probe requests sent to hostapd with the given probability, must be a 1712# floating point number in the range [0, 1). 1713#ignore_probe_probability=0.0 1714# 1715# Ignore authentication frames with the given probability 1716#ignore_auth_probability=0.0 1717# 1718# Ignore association requests with the given probability 1719#ignore_assoc_probability=0.0 1720# 1721# Ignore reassociation requests with the given probability 1722#ignore_reassoc_probability=0.0 1723# 1724# Corrupt Key MIC in GTK rekey EAPOL-Key frames with the given probability 1725#corrupt_gtk_rekey_mic_probability=0.0 1726 1727##### Multiple BSSID support ################################################## 1728# 1729# Above configuration is using the default interface (wlan#, or multi-SSID VLAN 1730# interfaces). Other BSSIDs can be added by using separator 'bss' with 1731# default interface name to be allocated for the data packets of the new BSS. 1732# 1733# hostapd will generate BSSID mask based on the BSSIDs that are 1734# configured. hostapd will verify that dev_addr & MASK == dev_addr. If this is 1735# not the case, the MAC address of the radio must be changed before starting 1736# hostapd (ifconfig wlan0 hw ether <MAC addr>). If a BSSID is configured for 1737# every secondary BSS, this limitation is not applied at hostapd and other 1738# masks may be used if the driver supports them (e.g., swap the locally 1739# administered bit) 1740# 1741# BSSIDs are assigned in order to each BSS, unless an explicit BSSID is 1742# specified using the 'bssid' parameter. 1743# If an explicit BSSID is specified, it must be chosen such that it: 1744# - results in a valid MASK that covers it and the dev_addr 1745# - is not the same as the MAC address of the radio 1746# - is not the same as any other explicitly specified BSSID 1747# 1748# Not all drivers support multiple BSSes. The exact mechanism for determining 1749# the driver capabilities is driver specific. With the current (i.e., a recent 1750# kernel) drivers using nl80211, this information can be checked with "iw list" 1751# (search for "valid interface combinations"). 1752# 1753# Please note that hostapd uses some of the values configured for the first BSS 1754# as the defaults for the following BSSes. However, it is recommended that all 1755# BSSes include explicit configuration of all relevant configuration items. 1756# 1757#bss=wlan0_0 1758#ssid=test2 1759# most of the above items can be used here (apart from radio interface specific 1760# items, like channel) 1761 1762#bss=wlan0_1 1763#bssid=00:13:10:95:fe:0b 1764# ... 1765
